奶头挺立呻吟高潮av全片,成人试看120秒体验区,性欧美极品v,A片高潮抽搐揉捏奶头视频

網絡技術

思科幀中繼點對多點子接口配置實例解析

時間:2024-08-26 16:56:15 網絡技術 我要投稿
  • 相關推薦

思科幀中繼點對多點子接口配置實例解析

  Cisco ACE是一個很常用的配置,下面小編為大家介紹了Cisco ACE的一個基本配置實例,希望大家能夠輕松掌握。

  幀中繼點對多點子接口拓撲圖如下:

  步驟一:配置R4的為幀中繼交換機。

  R4(config)#frame-relay switching //啟用frame-relay 交換

  R4(config)#interface serial 1/0

  R4(config-if)#encapsulation frame-relay

  R4(config-if)#frame-relay intf-type dce

  R4(config-if)#frame-relay lmi-type cisco (默認類型)

  R4(config-if)#frame-relay route 100 interface serial 1/1 101

  R4(config-if)#frame-relay route 200 interface serial 1/2 201

  R4(config-if)#clock rate 64000

  R4(config-if)#no shutdown

  R4(config-if)#exit

  R4(config)#interface serial 1/1

  R4(config-if)#encapsulation frame-relay

  R4(config-if)#frame-relay intf-type dce

  R4(config-if)#frame-relay lmi-type ansi

  R4(config-if)#frame-relay route 101 interface serial 1/0 100

  R4(config-if)#clock rate 64000

  R4(config-if)#no shutdown

  R4(config-if)#exit

  R4(config)#interface serial 1/2

  R4(config-if)#encapsulation frame-relay

  R4(config-if)#frame-relay intf-type dce

  R4(config-if)#frame-relay lmi-type q933a

  R4(config-if)#frame-relay route 201 interface serial 1/0 200

  R4(config-if)#clock rate 64000

  R4(config-if)#no shutdown

  步驟二:配置R2路由器

  R2(config)#interface serial 1/2

  R2(config-if)#encapsulation frame-relay //在接口下啟用幀中繼的封裝

  R2(config-if)#ip address 172.16.1.2 255.255.255.0

  R2(config-if)#no shut

  步驟三:配置R3路由器

  R3(config)#interface serial 1/2

  R3(config-if)#encapsulation frame-relay

  R3(config-if)#ip address 172.16.1.3 255.255.255.0

  R3(config-if)#no shut

  步驟四:配置R1,采用多點子接口,配置R1的幀中繼

  R1(config)#interface serial 1/2

  R1(config-if)#encapsulation frame-relay

  R1(config-if)#no ip add

  R1(config-if)#no shut

  R1(config-if)#exit

  R1(config)#interface serial 1/2.1 multipoint

  R1(config-subif)#ip address 172.16.1.1 255.255.255.0

  R1(config-subif)#frame-relay map ip 172.16.1.2 100 broadcast

  R1(config-subif)#frame-relay map ip 172.16.1.3 200 broadcast

  R1(config-subif)#exit

  R1(config)#exit

  步驟五:在R1使用show frame-realy lmi,show frame-relay pvc進行確認。

  步驟六:在R1,R2,R3上配置RIP,進行觀察。

  幀中繼點對多點子接口配置結果:R1,R2,R3能夠正確的學習到所有的路由。

【思科幀中繼點對多點子接口配置實例解析】相關文章:

思科交換機基本配置命令大全04-07

配置顯示器顏色配置文件方法教程12-02

思科交換機產品介紹07-18

思科最實用的技術命令大全04-02

思科認證考試費用有多少09-20

園路的植物配置方法10-13

揭秘美國思科是一家怎樣的公司06-11

dlink交換機配置方法07-16

二層組播的配置09-26

嵌入式系統接口技術07-16

主站蜘蛛池模板: 乌审旗| 中牟县| 南充市| 南安市| 威信县| 睢宁县| 西盟| 治多县| 兴仁县| 贡山| 永昌县| 阳信县| 庆阳市| 深圳市| 新密市| 郸城县| 富锦市| 南投县| 诸城市| 青神县| 博兴县| 阜阳市| 华容县| 克拉玛依市| 徐汇区| 祁东县| 宜君县| 年辖:市辖区| 高邮市| 泰安市| 武宣县| 交城县| 宁武县| 泰兴市| 浑源县| 孝昌县| 青田县| 永宁县| 台北县| 来宾市| 宣威市|